1 #
2 # ATM device configuration
3 #
4 mainmenu_option next_comment
5 comment 'ATM drivers'
6 if [ "$CONFIG_INET" = "y" ]; then
7 tristate 'ATM over TCP' CONFIG_ATM_TCP
8 fi
9 if [ "$CONFIG_PCI" = "y" ]; then
10 tristate 'Efficient Networks ENI155P' CONFIG_ATM_ENI
11 if [ "$CONFIG_ATM_ENI" != "n" ]; then
12 bool ' Enable extended debugging' CONFIG_ATM_ENI_DEBUG
13 bool ' Fine-tune burst settings' CONFIG_ATM_ENI_TUNE_BURST
14 if [ "$CONFIG_ATM_ENI_TUNE_BURST" = "y" ]; then
15 bool ' Enable 16W TX bursts (discouraged)' CONFIG_ATM_ENI_BURST_TX_16W
16 bool ' Enable 8W TX bursts (recommended)' CONFIG_ATM_ENI_BURST_TX_8W
17 bool ' Enable 4W TX bursts (optional)' CONFIG_ATM_ENI_BURST_TX_4W
18 bool ' Enable 2W TX bursts (optional)' CONFIG_ATM_ENI_BURST_TX_2W
19 bool ' Enable 16W RX bursts (discouraged)' CONFIG_ATM_ENI_BURST_RX_16W
20 bool ' Enable 8W RX bursts (discouraged)' CONFIG_ATM_ENI_BURST_RX_8W
21 bool ' Enable 4W RX bursts (recommended)' CONFIG_ATM_ENI_BURST_RX_4W
22 bool ' Enable 2W RX bursts (optional)' CONFIG_ATM_ENI_BURST_RX_2W
23 fi
24 fi
25 tristate 'Fujitsu FireStream (FS50/FS155) ' CONFIG_ATM_FIRESTREAM
26 tristate 'ZeitNet ZN1221/ZN1225' CONFIG_ATM_ZATM
27 if [ "$CONFIG_ATM_ZATM" != "n" ]; then
28 bool ' Enable extended debugging' CONFIG_ATM_ZATM_DEBUG
29 if [ "$CONFIG_X86" = "y" ]; then
30 bool ' Enable usec resolution timestamps' CONFIG_ATM_ZATM_EXACT_TS
31 fi
32 fi
33 # bool 'Rolfs TI TNETA1570' CONFIG_ATM_TNETA1570 y
34 # if [ "$CONFIG_ATM_TNETA1570" = "y" ]; then
35 # bool ' Enable extended debugging' CONFIG_ATM_TNETA1570_DEBUG n
36 # fi
37 tristate 'IDT 77201 (NICStAR) (ForeRunnerLE)' CONFIG_ATM_NICSTAR
38 if [ "$CONFIG_ATM_NICSTAR" != "n" ]; then
39 bool ' Use suni PHY driver (155Mbps)' CONFIG_ATM_NICSTAR_USE_SUNI
40 bool ' Use IDT77015 PHY driver (25Mbps)' CONFIG_ATM_NICSTAR_USE_IDT77105
41 fi
42 tristate 'Madge Ambassador (Collage PCI 155 Server)' CONFIG_ATM_AMBASSADOR
43 if [ "$CONFIG_ATM_AMBASSADOR" != "n" ]; then
44 bool ' Enable debugging messages' CONFIG_ATM_AMBASSADOR_DEBUG
45 fi
46 tristate 'Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)' CONFIG_ATM_HORIZON
47 if [ "$CONFIG_ATM_HORIZON" != "n" ]; then
48 bool ' Enable debugging messages' CONFIG_ATM_HORIZON_DEBUG
49 fi
50 tristate 'Interphase ATM PCI x575/x525/x531' CONFIG_ATM_IA
51 if [ "$CONFIG_ATM_IA" != "n" ]; then
52 bool ' Enable debugging messages' CONFIG_ATM_IA_DEBUG
53 fi
54 fi
55 if [ "$CONFIG_PCI" = "y" -o "$CONFIG_SBUS" = "y" ]; then
56 tristate 'FORE Systems 200E-series' CONFIG_ATM_FORE200E_MAYBE
57 if [ "$CONFIG_ATM_FORE200E_MAYBE" != "n" ]; then
58 if [ "$CONFIG_PCI" = "y" ]; then
59 bool ' PCA-200E support' CONFIG_ATM_FORE200E_PCA y
60 if [ "$CONFIG_ATM_FORE200E_PCA" = "y" ]; then
61 bool ' Use default PCA-200E firmware (normally enabled)' CONFIG_ATM_FORE200E_PCA_DEFAULT_FW
62 if [ "$CONFIG_ATM_FORE200E_PCA_DEFAULT_FW" = "n" ]; then
63 string ' Pathname of user-supplied binary firmware' CONFIG_ATM_FORE200E_PCA_FW ""
64 fi
65 fi
66 fi
67 if [ "$CONFIG_SBUS" = "y" ]; then
68 bool ' SBA-200E support' CONFIG_ATM_FORE200E_SBA y
69 if [ "$CONFIG_ATM_FORE200E_SBA" = "y" ]; then
70 bool ' Use default SBA-200E firmware (normally enabled)' CONFIG_ATM_FORE200E_SBA_DEFAULT_FW
71 if [ "$CONFIG_ATM_FORE200E_SBA_DEFAULT_FW" = "n" ]; then
72 string ' Pathname of user-supplied binary firmware' CONFIG_ATM_FORE200E_SBA_FW ""
73 fi
74 fi
75 fi
76 fi
77 if [ "$CONFIG_ATM_FORE200E_PCA" = "y" -o "$CONFIG_ATM_FORE200E_SBA" = "y" ]; \
78 then
79 int ' Maximum number of tx retries' CONFIG_ATM_FORE200E_TX_RETRY 16
80 int ' Debugging level (0-3)' CONFIG_ATM_FORE200E_DEBUG 0
81 if [ "$CONFIG_ATM_FORE200E_MAYBE" = "y" ]; then
82 define_tristate CONFIG_ATM_FORE200E y
83 else
84 define_tristate CONFIG_ATM_FORE200E m
85 fi
86 fi
87 fi
88 endmenu
This page was automatically generated by the
LXR engine.
Visit the LXR main site for more
information.